Gauge will work on battery packs as high as 350V Max. Requires a Pre-scaler to run on anything more than 36V. ![]() A second battery input is also provided to monitor voltage on a second battery. Using a clear backlit LCD Display and an intuitive user interface, all parameters can be recalled with just a button press. The LinkPRO selectively displays voltage, charge and discharge current, consumed amphours, remaining battery capacity and the time remaining of your battery bank. A new shunt selection feature enables the LinkPRO to measure currents up to 10,000 Amps. Xantrex 1800/12 Sine Wave Inverter 1800W 299.94 Was: 315.73 Free shipping SPONSORED Xantrex Freedom HF 1000 Inverter/Charger (8) 375.00 Free shipping SPONSORED Xantrex Freedom HF1800 Replacement Panel 808-1840 42.80 8.61 shipping 5 watching SPONSORED Xantrex XHR600-1. High performance measuring circuits, along with complex software algorithms, are used to exactly determine the remaining battery capacity. ![]() It is equipped with an internal programmable alarm relay, to run a generator when needed or to turn off devices when the battery voltage exceeds programmable boundaries.ĭefining the amount of energy available in a battery is a complex task since battery age, discharge current and temperature all influence the actual battery capacity. If your battery monitoring system contains an optional temperature. It selectively displays voltage, charge and discharge current, consumed amphours, remaining battery capacity and the time remaining of your battery bank. The interface box must be connected to the Xantrex Battery Monitor RJ12 expansion port. Reset by cycling the charger off and on.The LinkPRO can measure currents up to 10,000 Amps. HIGH BATTERY VOLTAGE SHUTDOWN DURING CHARGING:Ĭheck all charging sources (solar panels, alternators, other battery charges,Īnd so on) for proper voltage. Complete battery status Measures up to 10,000 amps Backlit LCD display. Be sure there is adequate ventilation around the unit. Xantrex LinkPro Battery Monitor 84-2031-00. The E-Xpert Pro selectively displays battery voltage, charge and discharge current, consumed amp hours, remaining battery capacity and time remaining. This error indicates that the Triac has overheated. TBS E-Xpert Xantrex EV Pro digital battery pack monitors measure current up to 9999A. LinkPRO Battery MonitorBattery Status At A GlanceDefining the amount of energy available in a. The Triac is used in the battery charging circuit in the FREEDOM series Provides critical information about the status of your battery bank. Reset by cycling the inverter OFF and ON or connecting Read your battery bank like a fuel gauge. Inverter overload caused by too large of a load or a short circuit on the output It selectively displays voltage, charge and discharge. This is potentially damaging to the unit. LinkPRO Battery Monitor Battery Status At A Glance The LinkPRO can measure currents up to 10000 Amps. See section in inverter owner's manual titled "Charging over-dischargedĪCpowerfromanoutsidesourcehasbeenfedtotheACoutputoftheinverter. Be sure there isĬaused by excessively discharged batteries, or a battery with a bad cell. Specifically designed to withstand the harsh operating environments of marine and vehicle applications, the Xantrex lithium battery lasts up to 6,000 cycles. Monitoring Monitors Battery Monitors Three products stood out in the battery monitor test: the Victron 700 and 702, thanks to their very precise calibration and two-bank capability, and the easy-to-install Xantrex LinkPro, and the self-calibrating Smartgauge from Balmar. Unit will reset automatically after it has cooled sufficiently. INVERTER LOW DC/BATTERY VOLTAGE SHUTDOWN:īattery voltage has dropped below 10.5 V for 12 V units or below 21 V for INVERTER HIGH DC/BATTERY VOLTAGE SHUTDOWN:īattery voltage has risen above 15.5 V for 12 V models or above 31 V for 24 (Error codes are the same for all models.) LinkPRO Battery MonitorBattery Status At A GlanceDefining the amount of energy available in a battery is a complex task. About the time Xantrex signed on to re-label the TBS monitors Victron found a new manufacturer to build their units, though I don’t know who it is. ![]() They have proven to be solid though very expensive units. The Error Code continues to flash until the error is corrected. Eventually Xantrex made the switch to all TBS built battery monitors such as the current Link-Lite and Link-Pro. The display alternates between the selected monitoring function and the Error Code. The following error codes are displayed when the LINK 2000 detects a problem.
0 Comments
Leave a Reply. |